3-7 www.mo xa .c o m Industrial Ethernet 3 Ethernet Media Converters and Extenders > CSM-200 Series 10/100BaseT(X) to 100BaseFX slide-in modules for the NRack System™ The CSM-200/400 modules are slide-in Ethernet-to-fiber media converters for the NRack System™. The modules provide media conversion from 10/100BaseT(X) to 100BaseFX (SC/ST connectors), and can be installed in any NRack System™ chassis. Introduction Specifications CSM-200 Series › ›LFP (Link Fault Pass-through) and FEF (Far End Fault) › ›Two different operation modes • Store-and-Forward • Pass Through › ›Auto Negotiation › ›Plug and Play › ›Hot-swap Technology Standards: IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X), 100BaseFX Interface RJ45 Ports: 10/100BaseT(X) Fiber Ports: 100BaseFX (SC/ST connectors) LED Indicators: PWR, Fiber Link, 10/100M (TP port) DIP Switches: DIP Function ON OFF 1 Auto Negotiation Enable Disable 2 Force TP Speed 100 Mbps 10 Mbps 3 Force TP Duplex Full Duplex Half Duplex 4 Link Fault Pass Through Enable Disable 5 Operating Mode Store-and-Forward Pass Through Optical Fiber 100BaseFX Multi-Mode Single-Mode Fiber Cable Type OM1 50/125 μm G.652 800 MHz*km Typical Distance 4 km 5 km 40 km Wave- length Typical (nm) 1300 1310 TX Range (nm) 1260 to 1360 1280 to 1340 RX Range (nm) 1100 to 1600 1100 to 1600 Optical Power TX Range (dBm) -10 to -20 0 to -5 RX Range (dBm) -3 to -32 -3 to -34 Link Budget (dB) 12 29 Dispersion Penalty (dB) 3 1 Note: When connecting a single-mode fiber transceiver, we recommend using an attenuator to prevent damage caused by excessive optical power. Note: Compute the “typical distance” of a specific fiber transceiver as follows: Link budget (dB) > dispersion penalty (dB) + total link loss (dB). Physical Characteristics Dimensions: 86.8 x 124.3 x 21 mm (3.42 x 4.89 x 0.83 in) Weight: Product only: CSM-200-1213: 115 g (0.25 lb) CSM-200-1214/1218: 125 g (0.28 lb) Packaged: CSM-200-1213: 170 g (0.37 lb) CSM-200-1214/1218: 180 g (0.40 lb) Environmental Limits Operating Temperature: 0 to 55°C (32 to 131°F) Storage Temperature: -20 to 75°C (-4 to 167°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Power Requirements Input Voltage: 12 VDC Input Current: 180 mA @ 12 VDC max. Standards and Certifications Safety: UL 60950-1 EMC: EN 55022/24 EMI: CISPR 22, FCC Part 15B Class A EMS: EN 61000-4-2 (ESD): Contact: 4 kV; Air: 8 kV EN 61000-4-3 (RS): 80 MHz to 1 GHz: 3 V/m EN 61000-4-4 (EFT): Power: 1 kV; Signal: 0.5 kV EN 61000-4-5 (Surge): Power: 1 kV; Signal: 0.5 kV EN 61000-4-6 (CS): 150 kHz to 80 MHz: 3 V/m EN 61000-4-8 (PFMF) EN 61000-4-11 Freefall: IEC 60068-2-32 MTBF (mean time between failures) Time: 1,454,560 hrs Standard: Telcordia (Bellcore), GB Warranty Warranty Period: 5 years Details: See www.moxa.com/warranty