16-15 www.mo xa .c o m Smart Remote I/O > ioLogik 2500 Ethernet Series Remote Automation 16 ioLogik 2542 Specifications Inputs and Outputs Configurable DIOs (by software): 12 channels Analog Inputs: 4 channels Isolation: 3k VDC or 2k Vrms Digital Input Sensor Type: Wet Contact (NPN or PNP) and Dry Contact I/O Mode: DI or Event Counter Dry Contact: • On: short to GND • Off: open Wet Contact (DI to COM): • On: 10 to 30 VDC • Off: 0 to 3 VDC Common Type: 6 points per COM Counter Frequency: 2.5 kHz Digital Filtering Time Interval: Software configurable Digital Output Type: Sink I/O Mode: DO or Pulse Output Pulse Output Frequency: 5 kHz Over-Voltage Protection: 45 VDC Over-Current Protection: 1.5 A per channel @ 25°C Over-Temperature Shutdown: 175°C (min.) Current Rating: 500 mA per channel @ 25°C DIO Output Leakage Current: < 1 mA @ 30 VDC Analog Input Type: Differential input Resolution: 16 bits I/O Mode: Voltage / Current (software selectable) Input Range: ±10 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA (burnout detection) Accuracy: • ±0.1% FSR @ 25°C • ±0.3% FSR @ -10 and 60°C • ±0.5% FSR @ -30 and 70°C Sampling Rate: • All channels: 400 samples/sec • Per channel: 100 samples/sec Input Impedance: 1 mega-ohm (min.) Built-in Resistor for Current Input: 120 ohms Power Requirements Input Voltage: 9 to 48 VDC Input Current: 358 mA @ 24 VDC MTBF (mean time between failures) Time: 375,439 hrs Standard: Telcordia SR332 Common Specifications LAN Ethernet: • 4 switched 10/100 Mbps RJ45 ports • 1 optimized port for faster downstream communications with daisy-chained ioLogik E1200 units Note: The optimized daisy-chain port is not supported by the ioLogik E1261W-T, E1261H-T, or E1263H-T. Protection: 1.5 kV magnetic isolation Protocols: Modbus/TCP (slave), TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP Serial Interface: 2 RS-232/422/485 (software selectable) RJ45 ports Parity: None, Odd, Even Data Bits: 5, 6, 7, 8 Stop Bits: 1, 2 Flow Control: None, RTS/CTS, XON/XOFF Baudrate: 300 to 115200 bps Protocols: Modbus/RTU (master/gateway), serial tunnel mode (client/ server) Physical Characteristics Wiring: I/O cable max. 14 AWG Dimensions: 61 x 157 x 115 mm (2.4 x 6.18 x 4.53 in) Weight: Under 1265 g (2.79 lb) Mounting: DIN-rail (standard), wall (with optional kit) Storage Expansion Slot: Up to 32 GB microSD™ memory card (SDHC compatible) Note: For units operating in extreme temperatures, industrial-grade, wide- temperature SD cards are required. Inputs and Outputs Digital Inputs: 8 channels Configurable DIOs (by software): 8 channels Isolation: 3k VDC or 2k Vrms Digital Input Sensor Type: Wet Contact (NPN or PNP) and Dry Contact I/O Mode: DI or Event Counter Dry Contact: • On: short to GND • Off: open Wet Contact (DI to COM): • On: 10 to 30 VDC • Off: 0 to 3 VDC Common Type: 8 points per COM Counter Frequency: 2.5 kHz Digital Filtering Time Interval: Software configurable Digital Output Type: Sink I/O Mode: DO or Pulse Output Pulse Output Frequency: 5 kHz Over-Voltage Protection: 45 VDC Over-Current Protection: 1.5 A per channel @ 25°C Over-Temperature Shutdown: 175°C (min.) Current Rating: 500 mA per channel @ 25°C DIO Output Leakage Current: < 1 mA @ 30 VDC Power Requirements Input Voltage: 9 to 48 VDC Input Current: 274 mA @ 24 VDC MTBF (mean time between failures) Time: 467,032 hrs Standard: Telcordia SR332 ioLogik 2512 Specifications