3-12 www. m oxa. com Ethernet Media Converters and Extenders Ethernet Media Converters and Extenders > 3 IMC-P101 Series IEEE 802.3af PoE Ethernet-to-fiber media converters Introduction Specifications IMC-P101 series Ethernet-to-fiber media converters provide Ethernet media conversion from 10/100BaseT(X) to 100BaseFX (with SC or ST connectors). These converters are classified as power source equipment (PSE), and when used in this way provide up to 15.4 watts to IEEE 802.3af compliant powered devices (PDs), eliminating the need for additional wiring. The IMC-P101 converters support IEEE 802.3/802.3u/802.3x with 10/100M, full/half-duplex, and MDI/ MDI-X auto-sensing, providing a complete solution for your industrial Ethernet network. Power over Ethernet IMC-P101 Series › ›10/100BaseT(X) auto-negotiation and auto-MDI/MDI-X › ›IEEE 802.3af compliant PoE PSE equipment › ›Power failure alarm by relay output › ›Store-and-forward mode and pass through mode › ›-40 to 75°C operating temperature range (T models) › ›Redundant dual DC power inputs Technology Standards: IEEE 802.3 for 10BaseT IEEE 802.3u for 100BaseT(X), 100BaseFX IEEE 802.3af for Power-over-Ethernet Interface RJ45 Ports: 10/100BaseT(X) Fiber Ports: 100BaseFX (SC/ST connectors) LED Indicators: PWR1, PWR2, Fiber Link, 10/100M (TP port), PSE Indicator DIP Switches: DIP No. Function ON OFF 1 Auto Negotiation Enable* Disable 2 Force TP Speed 100 Mbps* 10 Mbps 3 Force TP Duplex Full Duplex* Half Duplex 4 Link Fault Pass Through Enable* Disable 5 Operating Mode Store-and-Forward* Pass Through 6 PSE Disable Enable* 7 P.R.R. (PD Remote Reset) Enable Disable* * Default DIP switch setting. Alarm Contact: One relay output with current carrying capacity of 1 A @ 24 VDC Optical Fiber 100BaseFX Multi-Mode Single-Mode Fiber Cable Type OM1 50/125 μm G.652 800 MHz*km Typical Distance 4 km 5 km 40 km Wave- length Typical (nm) 1300 1310 TX Range (nm) 1260 to 1360 1280 to 1340 RX Range (nm) 1100 to 1600 1100 to 1600 Optical Power TX Range (dBm) -10 to -20 0 to -5 RX Range (dBm) -3 to -32 -3 to -34 Link Budget (dB) 12 29 Dispersion Penalty (dB) 3 1 Note: When connecting a single-mode fiber transceiver, we recommend using an attenuator to prevent damage caused by excessive optical power. Note: Compute the “typical distance” of a specific fiber transceiver as follows: Link budget (dB) > dispersion penalty (dB) + total link loss (dB). Physical Characteristics Housing: Metal Dimensions: 144.45 x 122.3 x 51.65 mm (5.69 x 4.81 x 2.03 in) Weight: Product only: 525 g (1.16 lb) Packaged: 710 g (1.56 lb) Installation: DIN-rail mounting, wall mounting (with optional kit) Environmental Limits Operating Temperature: Standard Models: 0 to 60°C (32 to 140°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 85°C (-40 to 185°F) Ambient Relative Humidity: 5 to 95% (non-condensing)