4-25 www.mo xa .c o m 4 MGate™ EIP3000 Series Industrial Ethernet Industrial Ethernet Gateways > Each MGate™ EIP3000 gateway supports virtual serial ports for the remote PC. You can connect to the MGate™ EIP3000 through the COM port by using Moxa’s Real COM driver, with the actual physical When using termination resistors to prevent serial signal reflection, it is important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is Complex device networks that incorporate high amperage devices could be subject to electrical signal distortion from electrical connection over the Ethernet. The gateway supports up to 4 virtual COM port connections and offers greater flexibility when designing redundant control systems. discharges, magnetic noise, or common mode transients. MGate™ series products solve this problem by using built-in optical isolation. universally compatible with all environments, the EIP3000 has DIP switches on the bottom panel for setting the termination and pull high/ low resistor values. The serial redirector function allows the commands of a serial master (command initiator) to be redirected to the serial slave (command executor) on another port. In addition, a serial master can operate simultaneously with EtherNet/IP masters without changing the DF1 architecture or software. With the serial redirector function, MGate™ EIP3000 gateways can establish redundant control of legacy slave devices that were originally designed to be controlled by a single serial master. Built-in Isolation Specifications ProCOM Implements Control via COM Port Mapping Pull high/low Resistors and Terminator Selection Serial Redirector Function Maintains Original Master/Slave Connections Ethernet Interface Protocols: CIP (PCCC) on EtherNet/IP Number of Ports: 2 (1 IP, supports Ethernet cascading) Speed: 10/100 Mbps, Auto MDI/MDIX Connector: 8-pin RJ45 Magnetic Isolation Protection: 1.5 kV (built-in) Serial Interface Protocol: DF1 Full-duplex Number of Ports: EIP3170/3170I: 1 EIP3270/3270I: 2 Serial Standards: RS-232/422, software selectable Connectors: EIP3170/3170I: DB9 male for RS-232, terminal block for RS-422 EIP3270/3270I: DB9 male x 2 ESD Protection: 15 kV for all signals Serial Communication Parameters Data Bits: 8 Stop Bits: 1, 2 Parity: None, Even, Odd Flow Control: RTS/CTS, DTR/DSR (RS-232 only) Baudrate: 1200 bps to 921.6 kbps Serial Signals RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: Tx+, Tx-, Rx+, Rx-, GND Software Configuration Options: Serial Console, Telnet Console, Windows Utility Utility: MGate Manager for Windows 2000, Windows XP, Server 2003, Vista, Server 2008 (x86/x64), Windows Server 2008 R2, Windows 7/8/8.1 (x86/x64), Windows Server 2012 (x64), Windows 2012 R2 Support: Smart Routing, Serial Redirection, ProCOM, MXview, SNMP v1 (read only) Physical Characteristics Housing: Plastic, IP30 Weight: MGate EIP3170: 360 g (0.79 lb) MGate EIP3270: 380 g (0.84 lb) Dimensions: Without ears: 29 x 89.2 x 118.5 mm (1.14 x 3.51 x 4.67 in) With ears extended: 29 x 89.2 x 124.5 mm (1.14 x 3.51 x 4.90 in) Environmental Limits Operating Temperature: Standard Models: 0 to 60°C (32 to 140°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 85°C (-40 to 185°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Vibration: IEC 60068-2-6, IEC 60068-2-64 Shock: IEC 60068-2-27 Drop: IEC 60068-2-32 Power Requirements Input Voltage: 12 to 48 VDC Input Current: MGate EIP3170: 435 mA @ 12 VDC MGate EIP3170I: 555 mA @ 12 VDC MGate EIP3270: 435 mA @ 12 VDC MGate EIP3270I: 510 mA @ 12 VDC Power Connector: Terminal block