1-74 EDS-P206A-4PoE Series 1 Industrial Ethernet Switches Industrial Ethernet Switches > www. m oxa. com EDS-P206A-4PoE Series Introduction The EDS-P206A-4PoE switches are smart, 6-port, unmanaged Ethernet switches supporting PoE (Power-over-Ethernet) on ports 1 to 4. The switches are classified as power source equipment (PSE), and when used in this way, the EDS-P206A-4PoE switches enable centralization of the power supply and provide up to 30 watts of power per port. The switches can be used to power IEEE 802.3af/at compliant powered devices (PD), eliminating the need for additional wiring, and support IEEE 802.3/802.3u/802.3x with 10/100M, full/half-duplex, MDI/MDI-X auto-sensing to provide an economical solution for your industrial Ethernet network. Specifications 6-port unmanaged Ethernet switches with 4 IEEE 802.3af/at PoE+ ports › ›IEEE 802.3af/at compliant PoE and Ethernet combo ports › ›Up to 30 watts per PoE port › ›24/48 VDC wide range redundant power inputs › ›Intelligent power consumption detection and classification › ›Redundant dual VDC power inputs › ›-40 to 75°C operating temperature range (T models) Technology Standards: IEEE 802.3af/at for Power-over-Ethernet IEEE 802.3 for 10BaseT IEEE 802.3u for 100BaseT(X) IEEE 802.3x for Flow Control Processing Type: Store and Forward Switch Properties MAC Table Size: 1 K Packet Buffer Size: 512 KB Interface RJ45 Ports: 10/100BaseT(X) auto negotiation speed, Full/Half duplex mode, and auto MDI/MDI-X connection Fiber Ports: 100BaseFX ports (SC/ST connector) PoE Pinout: V-, V-, V+, V+ for pin 1, 2, 3, 6 (Endspan, MDI-X Alternative A) Optical Fiber 100BaseFX Multi-Mode Single-Mode Fiber Cable Type OM1 50/125 μm G.652 800 MHz*km Typical Distance 4 km 5 km 40 km Wave- length Typical (nm) 1300 1310 TX Range (nm) 1260 to 1360 1280 to 1340 RX Range (nm) 1100 to 1600 1100 to 1600 Optical Power TX Range (dBm) -10 to -20 0 to -5 RX Range (dBm) -3 to -32 -3 to -34 Link Budget (dB) 12 29 Dispersion Penalty (dB) 3 1 Note: When connecting a single-mode fiber transceiver, we recommend using an attenuator to prevent damage caused by excessive optical power. Note: Compute the “typical distance” of a specific fiber transceiver as follows: Link budget (dB) > dispersion penalty (dB) + total link loss (dB). Power Requirements Input Voltage: 24/48 VDC, redundant dual inputs Operating Voltage: 22 to 57 VDC Input Current: 5.48 A @ 24 VDC Overload Current Protection: Present Connection: 1 removable 4-contact terminal block Reverse Polarity Protection: Present Power Consumption: Max. 11.52 W full loading without PDs’ consumption Power Budget: Max. 120 W for total PDs’ consumption Max. 30 W for each PoE port Physical Characteristics Housing: Metal IP Rating: IP30 protection Dimensions: 50.3 × 115 × 70 mm (1.98 x 4.53 x 2.76 in) Weight: 375 g (0.83 lb) Installation: DIN-rail mounting, wall mounting (with optional kit) Environmental Limits Operating Temperature: Standard Models: 0 to 60°C (32 to 140°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 85°C (-40 to 185°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Standards and Certifications Safety: UL 508 EMC: EN 55022/24 EMI: CISPR 22, FCC Part 15B Class A EMS: IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV IEC 61000-4-3 RS: 80 MHz to 1 GHz: 20 V/m IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV IEC 61000-4-6 CS: Signal: 10 V IEC 61000-4-8