IP Surveillance 19-37 www.mo xa .c o m IP Surveillance > VPort 461A Series 19 Superior video performance, 1-channel H.264/MJPEG industrial video encoders VPort 461A Series The VPort 461A 1-channel industrial video encoder with H.264 video compression algorithm provides the best video quality on the market, but with a smaller bandwidth requirement than other video compression standards. In addition, to meet various video stream requirements, the VPort 461A can provide up to 3 video streams simultaneously using H.264 and MJPEG compression formats. Video streams can be used for different purposes, such as viewing, recording, and analysis. In addition, the rugged industrial design, Specifications Introduction › ›Supports up to 3 video streams simultaneously for H.264 and MJPEG › ›Up to Full D1 resolution (720 x 480) @ 90 FPS for 3 video streams with legacy analog video images › ›Video latency under 200 ms › ›2 Ethernet ports for cascade and Ethernet port redundancy › ›Moxa DynaStream™ function support for network efficiency › ›ONVIF support for standardization and interoperability › ›Local storage capability with SD card slot › ›Industrial design with -40 to 75°C operating temperature which includes a -40 to 75°C operating temperature, IP30 protection, and industrial certifications, make the VPort 461A suitable for harsh environments. The VPort 461A is equipped with Moxa’s innovative DynaStream™ technology, which allows you to change the video frame rate automatically. With DynaStream™, you can control your network bandwidth budget and simplify network system management. The CBR Pro™ function guarantees the lowest packet loss for limited bandwidth transmissions to ensure that images will not exhibit the mosaic effect. Video Video Compression: H.264 (MPEG4 part 10), MJPEG Video Inputs: 1 (BNC connector) Video Outputs: Over Ethernet Video Streams: 3, H.264 or MJPEG video streams NTSC/PAL: Auto-sensing or manual Video Resolution and FPS (frames per second): NTSC PAL Size Max. FPS Size Max. FPS QCIF 176 x 112 30 176 x 144 25 CIF 352 x 240 30 352 x 288 25 VGA 640 x 480 30 640 x 480 25 4CIF 704 x 480 30 704 x 576 25 Full D1 720 x 480 30 720 x 576 25 Video Viewing: • DynaStream™ support for changing the video frame rate automatically • Adjustable image size and quality • Timestamp and text overlay • Maximum of 10 simultaneous unicast connections, 50 multicast clients • CBR Pro™ support for accurate streaming bit rate control • Image manipulation: 180° rotation • Image tuning: control brightness, contrast, saturation Audio Audio Inputs: 1 Line-in or mic-in with 3.5 mm phone jack Audio Outputs: 1 Line-out with 3.5 mm phone jack Audio Format: Mono, PCM (G.711) Network Protocols: IPv4/v6, UDP, HTTP, SMTP, FTP, NTP, DNS, DHCP, UPnP, RTP, RTSP, ICMP, IGMPv3, QoS (ToS), SNMP V3, DDNS, Modbus/ TCP, 802.1X, SSH/HTTPS Ethernet: 2 10/100BaseT(X) Ethernet ports, RJ45 connector Serial Port PTZ Ports: 1 RS-232 or RS-422/485 port, terminal block connector, 115.2 kbps COM Ports: 1 RS-232 or 485 port, DB9 male connector, 115.2 kbps Console Port: 1 RS-232 port, RJ45 connector Local Storage SD Socket: Standard SD socket, V2.0 (SDHC) GPIO Digital Inputs: 2, max. 8 mA High: +13 to +30 V; Low: -30 to +3 V Relay Outputs: 2, max. 24 VDC @ 1 A LED Indicators STAT: Indicates if system is booted up properly or not PWR1: Power 1 PWR2: Power 2 FAULT: Can be configured to correspond to system alarm, power failure, or disconnected network VIDEO: Video input signal PTZ: Indicates if PTZ or COM port data has been transmitted SD: Indicates if SD card was mounted successfully Power Requirements Input Voltage: 12 to 32 VDC, or 18 to 30 VAC Input Current: 0.85 A @ 12 VDC; 0.3 A @ 32 VDC; 0.85 A @ 18 VAC; 0.56 A @ 30 VAC Physical Characteristics Housing: Metal, IP30 protection Dimensions: 46 x 134 x 105 mm (1.81 x 5.31 x 4.13 in) Weight: 710 g (1.57 lb), including DIN-rail mounting kit Installation: DIN-rail mounting (standard), wall mounting (optional) Alarms Intelligent Video: Camera tampering Video Motion Detection: Includes sensitivity tuning Scheduling: Daily repeat timing schedule Imaging: JPEG snapshots for pre/trigger/post alarm images