10-38 www. m oxa. com NPort® 5600 Series Serial-to-Ethernet Device Servers Serial-to-Ethernet Device Servers > 10 Specifications Appearance Ethernet Interface Number of Ports: 1 Speed: 10/100 Mbps, auto MDI/MDIX Connector: 8-pin RJ45 Magnetic Isolation Protection: 1.5 kV built-in Optical Fiber Interface (for -M-SC and -S-SC) 100BaseFX Multi-Mode Single-Mode Fiber Cable Type OM1 50/125 μm G.652 800 MHz*km Typical Distance 4 km 5 km 40 km Wave- length Typical (nm) 1300 1310 TX Range (nm) 1260 to 1360 1280 to 1340 RX Range (nm) 1100 to 1600 1100 to 1600 Optical Power TX Range (dBm) -10 to -20 0 to -5 RX Range (dBm) -3 to -32 -3 to -34 Link Budget (dB) 12 29 Dispersion Penalty (dB) 3 1 Note: When connecting a single-mode fiber transceiver, we recommend using an attenuator to prevent damage caused by excessive optical power. Note: Compute the “typical distance” of a specific fiber transceiver as follows: Link budget (dB) > dispersion penalty (dB) + total link loss (dB). Serial Interface Number of Ports: 8 or 16 Serial Standards: NPort 5610: RS-232 NPort 5630: RS-422/485 NPort 5650: RS-232/422/485 Connector: RJ45 (8 pins) RS-485 Data Direction Control: ADDC® (Automatic Data Direction Control) Pull High/Low Resistor for RS-485: 1 kΩ, 150 kΩ (NPort 5650-8/16) Serial Communication Parameters Data Bits: 5, 6, 7, 8 Stop Bits: 1, 1.5, 2 Parity: None, Even, Odd, Space, Mark Flow Control: DSR/DTR and RTS/CTS (RS-232 only), XON/XOFF Baudrate: 50 bps to 921.6 kbps Serial Signals RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND RS-485-2w: Data+, Data-, GND Software Network Protocols: ICMP, IPv4, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1, HTTP, SMTP, SNTP, ARP, PPP, SLIP, RTelnet, RFC2217 Configuration Options: Web Console, Telnet Console, Windows Utility Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux Real TTY Drivers: Linux 2.4.x, 2.6.x, 3.x Mini Screen with Push Buttons (for standard temp. models) LCD Panel: Liquid Crystal Display on the case Push Buttons: Four push buttons for convenient on-site configuration Physical Characteristics Housing: Metal Weight: NPort 5610-8: 3,340 g (7.36 lb) NPort 5610-8-48V: 3,160 g (6.97 lb) NPort 5630-8, 5650-8-S-SC, 5650-8-M-SC: 3,380 g (7.45 lb) NPort 5650-8: 3,360 g (7.41 lb) NPort 5610-16: 3,420 g (7.54 lb) NPort 5610-16-48V: 3,260 g (7.19 lb) NPort 5630-16: 3,400 g (7.50 lb) NPort 5650-16: 3,460 g (7.63 lb) NPort 5650-16-S-SC, 5650-16-M-SC: 3,440 g (7.58 lb) NPort 5650-8-HV-T: 3,720 g (8.20 lb) NPort 5650-16-HV-T: 3,820 g (8.42 lb) Dimensions: Without ears: 440 x 45 x 198 mm (17.32 x 1.77 x 7.80 in) With ears: 480 x 45 x 198 mm (18.90 x 1.77 x 7.80 in) Environmental Limits Operating Temperature: Standard Models: 0 to 55°C (32 to 131°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) High Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F) Storage Temperature: Standard Models: -20 to 70°C (-4 to 158°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) High Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Ethernet RJ45 10/100 Mbps AC power switch Note: LCD panel and configuration buttons not available with wide-temp. models Serial ports (50 bps to 921.6 kbps, RJ45 connectors) NPort® 5610: RS-232 NPort® 5630: RS-422/485 NPort® 5650: RS-232/422/485 AC power input 100 to 240 VAC input, 47 to 63 Hz LCD panel Reset button Push buttons LED indicators system status, serial Tx/Rx